Mar 08, 2012 · Page 1 of 2 - How to control the wireless radio on a home router. - posted in Home Automation: NOTE: Applies to routers flashed with Tomato or DD-WRT firmware. I recently upgraded my home router, from an ancient Netgear FVS318 plus WG102 Wireless Access Point, to a Cisco/Linksys e3000. Within a few days, I replaced its stock firmware with TomatoUSB (Toastmans build) and it is running fine. The

Having this set to TKIP or TKIP+AES in conjunction with incorrect security mode noted above, is THE leading cause of not getting n/ac speeds in DD-WRT. See this link for more in depth info about AES which stands for Advanced Encryption System. WPA Shared Key. Available Settings: Anything My router (wrt160nV3), is experiencing this same issue in BrainSlayer build 23320 (dd-wrt.v24-23320_NEWD-2_K2.6_openvpn_small.bin). If I telnet and check wl status, the interface is showing "Mode: Ad Hoc" not Managed. A quick wl down and wl up returns the WiFi to working order. On Atheros-based WNDR3800, WNDR3700v2, WNR2200 WiFi LEDs are not turned on/off when Radio is turned on/off by WPS/WiFi buttons. This is a problem on all builds up to latest r25974. If gpio info is needed for the LEDs, I am willing to test/verify, if possible. For reference, the WiFi LED turns on/off correctly on Ralink since r25947. It would be Nov 06, 2009 · Posted: Sat May 30, 2009 20:09 Post subject: WRT54G v8 radio off after cold boot: My WRT54G v8 (yeah, I know its crappy) works fine thanks to dd-wrt. The problem is, when it cold boots (for example when you plug AC out and in again) the radio never works. I get TX errors (22 errors) and then the radio seem to give up. Arg 1 is the country abbreviation Arg 2 is the band(a or b) (editors note: only b seems to be recognized in dd-wrt v22) Example: wl channels_in_country JP b curpower. Return current tx power settings evm. Start an EVM test on the given channel, or stop EVM test. Arg 1 is channel number 1-14, or "off" or 0 to stop the test. Posted: Thu Feb 02, 2012 7:08 Post subject: Loaded dd-wrt and radio is OFF or not showing: Hi all, I loaded dd-wrt on my Dlink DIR825 and with super channel enabled. It seems dd-wrt couldn't find the Radio. When I loaded factory image, radio would show up and worked fine, but when I loaded dd-wrt, in wirelesss->basic settings, radio will show

I've tried changing the "Enable Wireless Router Radio" check boxes from checked to unchecked (both for 2.4GHz b/g/n and 5GHz a/n/ac sections), hit apply, then changed it back to checked, hit apply, and again I see the OFF status in the Home page.

So I've turned on radio scheduling for both my 2.4g and my 5g radio. It turns off fine with the schedule but the radios will not turn on themselves again. I've resorted to settling on a reboot scheduled for 1 minute after the scheduled turn-on time and when it reboots it comes back. Mar 08, 2012 · Page 1 of 2 - How to control the wireless radio on a home router. - posted in Home Automation: NOTE: Applies to routers flashed with Tomato or DD-WRT firmware. I recently upgraded my home router, from an ancient Netgear FVS318 plus WG102 Wireless Access Point, to a Cisco/Linksys e3000. Within a few days, I replaced its stock firmware with TomatoUSB (Toastmans build) and it is running fine. The I've tried more builds from the year 2018 and the radio is off on all builds. Radio MAC address is present, TX/RX counters are on zero and cannot get wireless working. Wireless radio was working fine with Tomato, but I would like to use DD-WRT instead. In logs are the following warnings: Script to restart the radio on a DD-WRT router. GitHub Gist: instantly share code, notes, and snippets.

So, having DD-WRT v24-sp2 running on my wonderful D-Link DIR-320 I have configured the Radio Time Restriction in such way it' starting daily at 18:00 (when normally I should be back from work) and runs until 24:00 (when I should be asleep).

running DD-WRT v3.0-r29048 std (02/05/16) yes, I have enabled the switching under services. SES / AOSS / EZ-SETUP / WPS Button. another funny thing, the wireless LED on the router is backwards, when I disable wireless and reboot the router, it comes on. hi i recently upgrade my WRT3200ACM to dd-wrt and the two leds indicators for wifi 2.4 and 5ghz are off, i have radio on and wifi active. thats